Cabinet - Pine Corner Cabinet

[ Pobierz całość w formacie PDF ]
I"x8"x8' pine
FINISHED
CUT
SlZE
(Number in brackets isnumber of pieces
needed)
INSTRUCTIONS
Cutting
1. The basic ''shell" of the corner cabinet is
cut from 1/2" plywood and includesparts
AL, AR and two parts
B,
(see Fig. 1 and
2).
Cut to the dimensions as shown, then glue
and nail partstogether as illustrated.
2. Laminatepiecesof 1"x5" pine to make
the top, part C as shown in Fig.
3.
Cut part C
to shape.
3.
Cut parts
D
and
G
to size, notingthat one
edge along each length is cut at 221/z0, (see
top view).
4. Cut drawer front
H
to size, then cut or rout
the outside edges as you choose. In this
case, edges are bevelled.
5. Use parts J (panels),
K
(stiles)and
L
(rails) to make the two cabinet doors, (see
CABINET
(1) 2O"x2O"x
3h"
-
C
(2) 18%
"
~18~/z
"
X
l/z
"
plywood
-
B
3h"
-
D
(1) 7lh
"
x
18%
"
X
3h
"
-
E
BY
J.D. RIDLEY
MATERIALS
3h"
-K
(4) 2"~61/2"~
3h"
-
L
(2) 5%"~21"~
3hN
-
M
. .
ROUGH CUT SlZE
Also required:
4'x4' xl/2" plywood
(2) pr. flush-mount hinges
1"x3"x14' pine
(2) knobs
l"x5"xl6', pine
(1) drawer handle
FIG.l
ACK CORNER DETAl
FIG.2
36
Canadian
Workshop,
July
1989
(2)2"~29"~
(4)
2"~18"~
.
front edges of the plywoodcabinet base, the
top of
E
should be flush with the top, part B.
The top edge of
F
should be flush with the
top of the bottom shelf, B. Glue and nail this
frame to the cabinet base.
2.
Glue and nail parts G to parts
B,
D, AL
and AR.
3.
Glue and clamp drawer front
H
to part
E,
from
11/4"
from the top of
E
to the top of
H.
4. Attach top C to the top of cabinet base B
using
1
"
x
#8
screws from the underside of
I
B.
Back edges of C should be flush with
back edges of AL and AR, allowing front
edges of C to overhang the cabinet front by
1/4
".
5. Glue and nail parts M to back edges of C
I
DOORS-MAKE
2
I
I
Fig. 4). Grooves in stiles
K
are
%"
deep,
7.
Cut part
E
and
F
to size.
tenons on the ends of rails L are also
l/2"
and to each other also along the mitred
long.
back corner.
6.
Sand, then finish cabinet and doors as
one end of each part M at 45O, then cut M to
1.
Dowel, then glue and clamp part
E
and
F
you choose. Attach doors to cabinet
shape.
Assembly
between parts
D.
When placed onto the
(hinges) and attach remaining hardware.
Continued
6.
Make a template for part M (Fig. 5). Cut
'
38
.-.
-
-
-
Canadian
Workshop,
July
1989
-
---
--
-.
-
- -
[ Pobierz całość w formacie PDF ]